ELECTRICAL POWER ELECTRONIC TRAINING SYSTEM EDUCATIONAL EQUIPMENT VOCATIONAL TRAINING LABORATORY EQUIPMENT
PN: GTET-1013A
Picture for reference:
Order No.: GT2021061801
Specification:
POWER ELECTRONICS TRAINER DESCRIPTION
This Power Electronics Trainer System is a versatile, robust and easy to use training kits used for teaching, learning and constructing circuits based on power electronics theory and fundamentals. Suitable for basic power electronics circuit designs and application.
It is a self-contained system, equipped with the power supply modules, various experiment plug in modules, user guide, experiment manual, connection cables and related accessories.
For each experiment, circuits are constructed by the user using safety connection cables and built-in connector sockets to avoid any hazardous risk to the user and also the training kit itself. Each experiment is detailed in the lab workbook.
Each of these modules can be directly placed on the laboratory lab bench or can be mounted onto an optional robust table top frame rack (ITEM: TFR-001) when conducting experiments. Connection using 4mm sockets.
The following Power Electronics Experiments are covered used the various related training modules.
These modules enable students to investigate a wide range of power electronics syllabus practical topics. Students investigate each topic with hands on experimentation, circuit construction and evaluation tasks which are provided in the experimental manual/workbook. Each module is equipped with clearly labeled block diagram and built-in connection interface and test points.
1. SINGLE PHASE POWER SUPPLY
• 2 x 15V-0-15V AC output, maximum 800mA
• ±12V DC power supply, maximum 1A
• Input supply: Single phase 240VAC/50Hz
• On/Off power switch with indicator
• Fuse protection
2. LOAD MODULE
• Star connected load x 1
• Delta connected load x1
• Resistor: 10KΩ/2W x1
• Capacitor:1000uF/50Vx1, 10uF/50V x1
• Inductor: 1.5mH x1 , 3mH x1
• DC Fan x1
• Lamp bulb with socket x1
3. FIRING CONTROL UNIT MODULE
• Control firing angle for SCR and TRIAC
• Control duty cycle of PWM for chopper and inverter
• Zero crossing detector
• Switch for Mode selector
• Reset button
• Fuse protection
• Isolation protection between control unit and application circuits
• Suitable for single phase and three phase control application
• Input power: 12VDC
4. TYRISOTR (SCR) & TRIAC MODULE
• SCR R and RC firing circuit
• SCR: VDRM: 600V, IT(rms): 12A, ITAV : 8A, IGT: 15mA
• Free wheeling Diode: VRRM : 50V, ITAV : 1A, IFSM : 30V
• Built-in resistor, variable resistor and capacitor for thyristor R and RC firing
• TRIAC circuit
• TRIAC: VDRM = 500V, IT(rms) = 4A, IGT = 25mA
5. UJT & PUT MODULE
• UJT oscillator circuit.
• UJT using 2N2647
• PUT oscillator circuit.
• PUT using 2N6028
• Input: 12VDC
6. IGBT & POWER MOSFET MODULE
• IGBT circuit.
• IGBT: VCE = 600V, Ic = 10A, VCE(sat) = 1.5V, IF = 20A (Tc = 25 degree C), 10A(Tc = 100 degree C)
• Power MOSFET circuit.
• Power MOSFET: VDSS =55V, ID = 17A, RDS(on) = 0.07Ω
7. SINGLE PHASE UNCONTROLLED CONTRO MODULE
• Single Phase Half-Wave Uncontrolled Rectifier using power diode
• Single Phase Full-Wave Uncontrolled Rectifier using power diode
• Single Phase Full-Wave Uncontrolled Bridge Rectifier using power diode
• Power Diode: VRRM : 50V, ITAV : 1A, IFSM : 30A
8. SINGLE PHASE CONTROLLED RECTIFIER MODULE
• Single Phase Half-Wave Controlled Rectifier using Thyristor(SCR)
• Single Phase Full-Wave Controlled Rectifier using Thyristor(SCR)
• SCR: VDRM: 600V, IT(rms): 12A, ITAV : 8A, IGT: 15mA
9. SINGLE PHASE CONTROLLED BRIDGE RECTIFIER MODULE
• Single Phase Half Controlled Bridge Rectifier using Thyristor(SCR)
• Single Phase Fully Controlled Bridge Rectifier using Thyristor(SCR)
• SCR: VDRM: 600V, IT(rms): 12A, ITAV : 8A, IGT: 15mA
10. SINGLE PHASE AC VOLTAGE CONTROLLER MODULE
• Single Phase Bi-Direction AC Voltage Controller using TRIAC
• Single Phase Uni-Direction AC Voltage Controller using TRIAC
• Single Phase Frequency Converter using TRIAC
• TRIAC: VDRM : 500V IT(RMS) = 4A, IGT = 25mA
11. DC CHOPPER MODULE
• Step-Down Chopper using Power MOSFET
• Step-Down Chopper using IGBT
• Step-Up Chopper using Darlington Transistor
12. SINGLE PHASE BRIDGE INVERTER MODULE
• Single Phase Full Bridge Inverter.
• Single Phase Half Bridge Inverter.
• Inverter circuits using Power MOSFET
13. THREE PHASE UNCONTROLLED RECTIFIER MODULE
• Three Phase Half-Wave Uncontrolled Rectifier using power diode
• Three Phase Full-Wave Uncontrolled Bridge Rectifier using power diode
• Three Phase Full-Wave Uncontrolled Rectifier (Six Pulse Rectifier) using power diode
• Power Diode: VRRM : 50V, ITAV : 1A, IFSM : 30A
14. THREE PHASE CONTROLLED RECTIFIER MODULE
• Three Phase Half-Wave Controlled Rectifier using Thyristor(SCR)
• Three Phase Fully Controlled Bridge Rectifier using Thyristor(SCR)
• Three Phase Half Controlled Bridge Rectifier using Thyristor(SCR)
• SCR: VDRM: 600V, IT(rms): 12A, ITAV : 8A, IGT: 15mA
15. THREE PHASE BRIDGE INVERTER MODULE
• Three Phase Bridge Inverter using Power MOSFET
16. THREE PHASE AC VOLTAGE CONTROLLER MODULE
• Three Phase Uni-Direction AC Voltage Controller using TRIAC
• Three Phase Bi-Direction AC Voltage Controller using TRIAC
• TRIAC: VDRM : 500 IT(RMS) : 4A , IGT: 25mA
17. THREE PHASE POWER SUPPLY
• 2 x 26V AC line voltage three phase power supply, maximum 500mA.
• 3 pole MCB (Miniature Circuit Breaker) protection.
• Start and Stop push buttons
• Input supply: Three phase 415VAC/50Hz (L1, L2, L3, N, PE)
18. SAFETY CONNECTION LEAD CABLES
• 4mm Connecting Leads Cable set
19. SAFETY CONNECTION LEAD CABLES
• 4mm Safety Connecting Leads Cable set
20. MOUNTING FRAME
• Material : Metal / Aluminum
• Side Frame: T-Shape
• 2 layer
21. MAIN CORD & DC ADAPTOR
• Come with 1 set Main Cord
• 12VDC 1A Power Adaptor
Packing&Shipping
Solid plywood box and normally ship by sea, but if the size is not big, also by air, FedEx or DHL, TNT and so on.
Company Profile
Guangzhou Guangtong Educational Equipment Co.,LTD is a well-known high-tech company, we participate in many international educational tenders and help our customer win the tender.
We are specialized in development and manufacturing of professional Educational Equipment including automotive teaching equipment, air conditioning and refrigeration teaching equipment, electrical and electronic teaching equipment, lift teaching, solar energy trainer, electric car training device and other vocational training equipment etc.
GTEE is located in Baiyun District, Guangzhou City and adjacent to Guangzhou Baiyun International Airport.
With our several years of design, development, manufacturing and international service experience and expertise, GTEE is growing up and developing very fast. We continuously focus on providing high quality products with competitive price and reliable after sale services for our overseas customers. We will response to our customers within 24 hours after get the feedback and requirements.
Show Room:
Customer Photos:
FAQ
Q: Are you trading company or manufacturer?
A: We are manufacturer.
Q: How long is your delivery time?
A: Depends on product quantity and stock. Please check with our sales team.
Q: What are your terms of payment?
A: Payment<=5000USD, 100% in advance.
Payment>=5000USD, 50% T/T in advance, 50% T/T balance before shipment.
Q: Do you offer aftersales support ?
A: Yes, of course, we will provide training materials together with the device, and also we can provide on-site training and installation if customer request. We also have technical engineer for online or remote support, and if within warranty, products parts damaged due to our quality problems, we will send parts via DHL to you for replacement for free as we seek long term cooperation with customers.
Q: How to have exclusive sales rights of GTEE?
A: Place order to GTEE, when the order amount reach certain level, GTEE and customer will negotiate about exclusive rights.
Or send your company profile to GTEE, after GTEE evaluation, start from general agents and gradually become exclusive agent.
Audited Supplier 
){kind=link}
){kind=link}